On paper, the instruction sheet and the traveler are two different documents, and the values written on one never get checked against the other. At a Threaded station they’re the same screen: the operator reads the step, enters the value next to it, and Threaded checks it against the spec on the spot.
#What it is
A station page is where an operator does the work. It shows the station’s queue, then the unit you’re working: its parts, tools and procedures, with fields for what the station records. Complete ends the unit’s visit, records everything, and moves the unit on.
The parts side of a station (picking serials, adding, swapping and scrapping parts) is covered in Parts at a Station.
#Rules
- Run is turned on per organization. See Feature Access and Billing.
#Recording values
- What a station records comes from the plant’s
specs/. A parameter is recorded only when its spec saysrecord: true. Otherwise it’s a setting: shown as a reference, such as an oven temperature, and never entered. - Text and choice parameters are always recorded.
- A number with a target and a tolerance, or with a minimum and maximum, is judged by those limits: In spec or out of spec.
- A number with no limits is recorded, never judged: No target: enter what you read.
- A choice is judged only when the spec names the expected choice. Text is never judged.
- A step marked pass/fail in its instruction is judged by the operator, with Pass / completed or Fail.
- A document, such as a drawing, is shown with its step and never recorded.
- Each value is stored for its step and its parameter. A step that measures two parameters records two values. If a station lists the same instruction twice, each copy records its own.
- A value saves as you leave its field, so a reload or another device shows it. Complete stamps the values and they never change after that. A retry after a hold records new values; the newest stamped values are the step’s result.
#Completing
- Complete is refused until the setup and changeover the work order owes the station are done, every step is recorded, every serial spot has a pick, and the unit isn’t on hold.
- A failed value, and a serial from outside the plant, must each be accepted as a deviation with a reason. Anything not accepted holds the unit.
- A held unit stays at the station. Nothing is counted and no parts are drawn until it’s resolved.
- Everything Complete records is recorded together. If any part of it is refused, nothing is recorded.
- Only a station whose routing step collects scrap asks for a yield and scrapped build parts. Elsewhere the whole batch moves on.
- Setup, changeover and closeout never hold a unit. Each failed value is accepted as a deviation or fixed.
#In the app
#Open a unit
Open a station from Run › Floor. Then click Start {unit} in the station’s panel, or click a unit in the station’s queue.
While a unit is open, View {count} in queue switches to another unit at this station. Next station: {name} shows where the unit goes next. The Work order details strip shows the work order, the part, the order quantity and the unit. Click the work order to open its page.
#Setup and changeover
Some stations need preparing before a work order runs there. If they do, opening the unit takes you to the prep page first.
- Setup is done once per work order at this station. The order’s other units use what was recorded. If another work order runs at the station in between, setup is due again.
- Changeover is done when the station last ran a different part.
Fill in the steps and click Complete. The order’s units then go straight to their run.
#Checks & specs, or Full instructions
The toggle beside the full screen button picks how procedures are shown:
- Checks & specs, the default: a form for each procedure with only the steps you act on: checks, spec lines, parameters and values to enter. Show step instructions opens a step’s full text and photos in place. Show full instructions opens the whole procedure beside the form, so you can keep entering values while you read.
- Full instructions: every step, with its text, photos, videos and drawings, as the instruction sheet shows it.
Each tablet remembers its choice. Values you’ve entered are kept when you switch.
#Fill in the values
Fields can be:
- Number. With limits, Threaded shows In spec when it passes. With none, it says No target: enter what you read.
- Fraction, for lengths. Enter Whole, Top and Bottom, for example 28 and 5/8.
- Choice. Pick one from the list.
- Text. Free text.
- Step result. Pass / completed or Fail.
- Photo. On a tablet, Tap to add photos opens the device’s camera or photo library. On a computer, Click to add photos, then pick Take photo with webcam or Choose photos from files…, or drop photos on the field. A required photo field shows At least one photo required. until you add one. A step keeps a limited number of photos, and the field says when it’s full.
An out-of-spec value shows Out of spec — completing this station will hold the unit.
#Complete the station
The button depends on the station:
- Complete station when there’s nothing to review.
- Review and complete station when there are failed values or serials from outside the plant, or the station collects scrap. It opens the Complete dialog.
- One button per designed return, such as Return to {name}, at a repair station with several.
The Complete dialog has two tabs:
- Deviations: each failed value and each serial from outside the plant. Tick Accept as a deviation and enter a Deviation reason for each one you accept, or click Accept all as deviations. Any you don’t accept hold the unit: enter a Hold reason, and click Hold unit. To change a reading instead, close the dialog and edit the field.
- Quantity and parts, at a station that collects scrap: the Yield, how many build parts were Scrapped and why (Add another reason splits them by reason), and the Material consumption table, where you mark parts Not used. See Parts at a Station.
Build parts that are neither yield nor scrapped are short; they leave the batch without a reason. If the yield is 0, the unit fails at the station.
Accepted deviations show on the unit’s record and in the work order’s Deviations.
#Where the unit goes
| The station | The unit |
|---|---|
| Has a next station on the route | Moves to it |
| Has a designed return (rework) | Moves to the return you chose |
| Is followed by a store | Lands in the store |
| Is the last on the route, and another part uses it here | Waits at the station as stock |
| Is the last on the route otherwise | Done |
What happens in a store is covered in Stores and Finishing Work Orders.
After Complete, the station goes on to the next unit of the same work order waiting here. If that was the order’s last unit here and it made a closeout due, it goes straight to the closeout. Otherwise it goes back to the queue and shows {unit} moved to {place}. Click Follow {unit} to open it at its next station.
#Ask for help
Click Needs help, enter a Help note and click Submit. The unit goes on hold. The map shows Needs help on the station, and the queue shows On hold.
A held unit is locked. To continue:
- Resolve clears the hold. Enter a note.
- Scrap scraps the whole unit where it stands. Enter a Scrap note. Every build part is scrapped, nothing more is drawn, and the station’s reserved parts and serials are released. Part of a held batch can’t be scrapped: resolve it and scrap the bad build parts at Complete.
Each hold is recorded with who raised it and why, and who ended it and how.
#Leave and notes
- Leave to {name} sends the unit out by a designed alternate exit, such as rework or scrap. Say why it’s leaving. Nothing is drawn, and the station’s reservations are released.
- More › Add note adds a note to the unit’s record. Notes can carry photos, and a barcode scanned into the text.
Notes, scrap and material changes from this visit are listed under Notes, scrap and material changes, with who did each. A note you added has an × to delete it until Complete. They also show in the work order’s activity.
#Closeouts
Some stations ask for a closeout once per work order, after its last unit has been through: what the order came to as a whole, such as the highest and lowest reading or a count.
The Closeouts panel above the station’s queue lists them:
- Due: every unit has been through. Click Close out.
- Units still to come: some units haven’t arrived yet. You can open it and start entering values; Threaded keeps them.
Fill in the values and click Complete closeout. Back to queue puts a closeout off; it stays Due in the panel. A work order stays on the floor until its closeouts are recorded.
#From the CLI or API
Every station action is in the API. Use threaded api call with these operations; see What Run Exposes.
run_format_units_save_step_values: save values as typed.run_format_units_complete_with_measurements: record values and complete, with a deviation reason for each failed value you accept.run_format_units_save_prep_valuesandrun_format_units_complete_prep: setup and changeover.run_format_units_help,run_format_units_resolve,run_format_units_scrapandrun_format_units_leave: hold, resolve, scrap a held unit, or leave.run_format_work_orders_save_closeout_valuesandrun_format_work_orders_complete_closeout: closeouts.run_format_execution_history_retrieve: a unit’s recorded values, visit by visit.